Featured content

Hello I like to install the wolfbox mirror and need some help. Does someone knows about the free FC‘s from cockpit electrical center witch free one is permanent + and witch free one is ignition switched on +?

The Grenadier back up light configuration utilizing the Baja Designs S2 Pro lights. For this project it is required for you to remove your plastic bumper covers and the brackets underneath and send them to us for modification. This is simple, using a Torx T30 driver to remove four bolts. Ship these to Design Build Go address listed on the website, which has more picture and video as well. These are hooked up to INT 2 switch on my Grenadier. I do not have them wired to reverses lights...

Who else's AC is batsh1t crazy and randomly blows hot air one day and cold the next on the exact same setting? I don't think the AC system got the attention it deserved during the 1.2 million miles of road testing, that's for sure. I love my new truck but it's the one thing that drives me nuts on pretty much a daily basis as I fiddle away at the controls and I'm surprised Ineos haven't found a fix for it yet. I gather it's down to sticky solenoid valves or such like and is probably an...

I just had my new Leitner front light bar and Baja Designs lights installed. It looks flipping awesome!! I have the red parking light hooked up to the Grenadier parking light switch so the red comes on with the parking lights. I have the low beams on overhead switch 5 and the high beams on overhead switch 2! Works perfect and lets me use those overhead switches a lot! Which is very cool. This was an expensive set up but worth it!

Bonjour, Is there a kit camera 360° available to fit with the electronics already factory installed in the Fieldmaster ? Thank you for help !

Hi all, Do anyone know if I can contact the Baja S2 chase lights on the leitner bracket directly into the reverse light circuit or do I need to use a relay to avoid getting a error message or blown fuse? Installing this weekend and can go either way.

I'm planning to put some lights up high on the roof rack. I have the Baja xl80s in my grill as an upgrade from the original off-road lights and they are pretty good. I want to wire the roof lights to the 25a circuit up on the roof. These seems to be my choices: KC hilites, 45" gravity titan bar. 23 amp draw Baja S8 Straight LED Light Bar combo 50", 20 amp draw Or 2 LP9 sport lights. 19 amp 4 Rigid 360-Series 6 inch, 2 drive and 2 spot. 24 amp draw if my math is correct What else is...

I ordered the Vision-X Grenadier Kit from a Deutschland e-store, the single LED 40W variant. Although it's written on the box that it's a Grenadier kit, it's not really... I received two complete single LED 40W Vision-X lamps with generic wiring harness (dual relay/fuse), two grille brackets and a bunch of screws and washers. - First, the brackets are a bit wide for the lamps, additional washers were needed for the clamping force to actually work and not bend the brackets. - The instructions...

I got a pair of KC Hilites Flex Era 4s in preparation for testing with BenTN's grill mounts. I watched youtube videos on how to wire them to Jeeps and other vehicles. Can anyone provide tips on how to wire them to my Grenadier? I plan to cut off the 3-position switch and relays and connect directly to the aux wires in the engine bay. I just have to figure out how to wire the yellow backlights and the main ones for independent switching on the cockpit overhead switch panel. Any indeas?

Bought a pair of Baja Designs 2x3 lights and mounted them in the rear using Leitner Designs’ bracket. I do not have the aux power panel, so I used the EXT 1 switch to power these lights. Basically ran a cable to the rear and mounted these two. Very straight forward. Super happy with the outcome.

WHAT YOU NEED STEDI Hex brackets (select size 48 to 53mm). The STEDI hex bracket came with a Torx Security key to tighten the bolts in the hex bracket. Not sure of the size because I could not get my Torx Security bits to fit properly. The brackets come with three M6 bolts of different sizes and types. One pair was the correct length to use in my setup. I also used a Nord Lock washer and a flat washer on the M6 bolt. The Nord Lock washer ensures corrugations do not loosen the bolts...

Has anyone installed their own ARB compressor? Did you buy a bracket or did you make one up? Thanks

Ultimate9 Releases Remote Digital Dash Speedometer: https://www.ultimate9.co/electrical/head-up-displays/browse-all/codebreaker-obd-hud-speedometer.html?utm_source=Klaviyo&utm_medium=campaign&_kx=mN2RVk-vkgBnEbT_mvthb9OMCSenIlJMRuHaFY0bcIo5ci-VQ_rx_B9w67ObqBdT.TCvQwB For US$55, Ultimate9 sells a wireless digital speedometer that uses a wireless OBDII dongle to read the vehicle computer data in a small footprint that can be placed above the warning light cluster. I’m still hoping Ineos...

Have anyone had any issues feeding power to their radio and getting a tiny bit of noise whine when the key is turned to on or if the engine is started? I wired my MXT275 to Int2 and with ignition off if I turned power on and int2 on, radio works perfect. However with ignition set to on or engine is on. I get this whine that comes through. I connected the power to center cubby cig and engine on no issues. Also tried an external power station and no issues. I suspect the power from...

Just say Leitner just released there INEOS GRENADIER Front Bumper Light Bar, they recommend Baja Design lights, I am going to look at KC lights on mine. Also saw he has the Aux light mounts for Rear ( Chase light Brackets) and Scene Light brackets for ACS Rack for the Side of the truck. https://www.leitnerdesigns.com/collections/the-grenadier-collection/products/ineos-grenadier-front-bumper-light-bar '

Has anyone had issues fitting vision X lights Was told they were plug and play with only a small adaption to the original housing needed….did this fit fine, had to swap connectors on the original wiring loom to fit new lights. When turned on using overhead switch and main beam lights come on for 2 seconds then off main beam stays on. Electrics not my thing does the relay need changing? Did try them with supplied wiring loom on spare 12v battery and worked fine.

ARB Agile Offroad instructions

Let me know if this link works…

Searched a bit but ran out of gas… I have a truck on order with the winch option, but am reconsidering as the aftermarket solutions come in to play. I’m wondering if I forego the winch option, what is different with respect to the wiring of a Trialmaster versus a Trialmaster with winch? (Specifically, what it would entail to add the winch later). I understand the springs are different with the winch option selected, but I plan on swapping out the stock springs regardless. Thanks in...

for what is this button?