Front Suspension Lower Control Arm Torque Specs

[Tazzieman]

@Glen my bad, torque is actually 295Nm for that 928 bolt.

 

[Glen]

I obtained replacement parts from the dealer and replaced the fasteners that secure the front axle lower control arm to the chassis. I took some measurements of the original bolts and the new ones. All dimensions are in inches.

Original Bolt 1       
Length    Station    Dia. 1    Dia. 2    Notes
4.488        1       0.5430              closest to threads
             2       0.5430              no significant difference Dia. 1 vs Dia. 2
             3       0.5450
             4       0.5460
             5       0.5455
             6       0.5460
             7       0.5475              closest to head

Original Bolt 2        
Length    Station    Dia. 1    Dia. 2    Notes
4.491       1        0.5420    0.5425    closest to threads
            2        0.5460    0.5443
            3        0.5450    0.5460
            4        0.5445    0.5450
            5        0.5450    0.5460
            6        0.5455    0.5460
            7        0.5465    0.5465    closest to head
        
New Bolt 1        
Length    Station    Dia. 1    Dia. 2    Notes
4.467       1        0.5420              closest to threads
            2        0.5425              no significant difference Dia. 1 vs Dia. 2
            3        0.5440
            4        0.5440
            5        0.5450
            6        0.5460
            7        0.5465              closest to head
        
New Bolt 2        
Length    Station    Dia. 1    Dia. 2    Notes
4.475       1        0.5420              closest to threads
            2        0.5425              no significant difference Dia. 1 vs Dia. 2
            3        0.5440
            4        0.5440
            5        0.5450
            6        0.5460
            7        0.5465              closest to head

The measurements of diameter were taken at seven equally spaced points between the flanged bolt head and just above the washer retention groove. Measurements were made along a line above the groove for Diameter 1 ("Dia. 1") and at 90° to that line for Diameter 2. The lengths were measured from the shortest edge of the flanged bolt head to the end of the bolt.

DISCUSSION OF MEASUREMENTS
I don't believe the lengths are significant enough to draw any reliable conclusions. The best way to detect stretch is to measure the bolt before and after stretch, and that wasn't done here. The bolt blanks are likely chopped to length in a non-precision process, heated, headed, stamped for the groove, then the threads and lead-in at the end are rolled. The last steps are likely heat treating and then plating. These steps don't result in precision starting lengths, all though I would note the longest original bolt is 0.024" longer than the shortest new bolt.

Original Bolt 2 is the most interesting: the measurements show about 0.001" thinning at the midpoint of the no-thread shank. This bolt is also out-of-round by about 0.001" to 0.002". The new bolts were as close to round (as measured at two points offset 90°) as I can measure accurately. I did not measure diameter across the threads because I'd expect a lot of natural variation in diameter there due to the manufacturing process.

OTHER OBSERVATIONS
There was some very minor thread damage on both of the original bolts where the bolt threads exited the nut (towards the bolt head). When I placed a tap with a 1.5 mm thread pitch on the two original bolts, the tap would not seat perfectly into the threads. This indicates the threads were likely stretched, but unfortunately, I did not test the new bolts with this procedure. Since the cross section is smaller across the threads, it makes sense that any plastic deformation would be more likely to occur in the threaded section.

CONCLUSIONS
I can't really come to any definite conclusions here. My assessment from just visually inspecting the orginal bolts is that they would be suitable for re-use. My measurements and check of the thread pitch leads me to believe that at least one - and maybe both - of the bolts just barely got into plastic deformation, albeit a very small amount. Like others, I'll be interested in a reply to my query of Ineos.

 

[Tazzieman]

I obtained replacement parts from the delaer and replaced the fasteners that secure the front axle lower control arm to the chassis. I took some measurements of the original bolts and the new ones. All dimensions are in inches.

<table>
<tr>
<th colspan="5">Original Bolt 1</th>
</tr>
<tr>
<th>Length</th>
<th>Station</th>
<th>Dia. 1</th>
<th>Dia. 2</th>
<th>Notes</th>
</tr>
<tr>
<td>4.488</td>
<td>1</td>
<td>0.5430</td>
<td></td>
<td>closest to threads</td>
</tr>
<tr>
<td></td>
<td>2</td>
<td>0.5430</td>
<td></td>
<td>no significant difference Dia. 1 vs Dia. 2</td>
</tr>
<tr>
<td></td>
<td>3</td>
<td>0.5450</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>4</td>
<td>0.5460</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>5</td>
<td>0.5455</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>6</td>
<td>0.5460</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>7</td>
<td>0.5475</td>
<td></td>
<td>closest to head</td>
</


<table>
<tr>
<th colspan="5">Original Bolt 2</th>
</tr>
<tr>
<th>Length</th>
<th>Station</th>
<th>Dia. 1</th>
<th>Dia. 2</th>
<th>Notes</th>
</tr>
<tr>
<td>4.491</td>
<td>1</td>
<td>0.5420</td>
<td>0.5425</td>
<td>closest to threads</td>
</tr>
<tr>
<td></td>
<td>2</td>
<td>0.5460</td>
<td>0.5443</td>
<td></td>
</tr>
<tr>
<td></td>
<td>3</td>
<td>0.5450</td>
<td>0.5460</td>
<td></td>
</tr>
<tr>
<td></td>
<td>4</td>
<td>0.5445</td>
<td>0.5450</td>
<td></td>
</tr>
<tr>
<td></td>
<td>5</td>
<td>0.5450</td>
<td>0.5460</td>
<td></td>
</tr>
<tr>
<td></td>
<td>6</td>
<td>0.5455</td>
<td>0.5460</td>
<td></td>
</tr>
<tr>
<td></td>
<td>7</td>
<td>0.5465</td>
<td>0.5465</td>
<td>closest to head</td>
</tr>
</table>
`


<table>
<tr>
<th colspan="5">New Bolt 1</th>
</tr>
<tr>
<th>Length</th>
<th>Station</th>
<th>Dia. 1</th>
<th>Dia. 2</th>
<th>Notes</th>
</tr>
<tr>
<td>4.467</td>
<td>1</td>
<td>0.5420</td>
<td></td>
<td>closest to threads</td>
</tr>
<tr>
<td></td>
<td>2</td>
<td>0.5425</td>
<td></td>
<td>no significant difference Dia. 1 vs Dia. 2</td>
</tr>
<tr>
<td></td>
<td>3</td>
<td>0.5440</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>4</td>
<td>0.5440</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>5</td>
<td>0.5450</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>6</td>
<td>0.5460</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>7</td


<table>
<thead>
<tr>
<th colspan="5">New Bolt 2</th>
</tr>
<tr>
<th>Length</th>
<th>Station</th>
<th>Dia. 1</th>
<th>Dia. 2</th>
<th>Notes</th>
</tr>
</thead>
<tbody>
<tr>
<td>4.475</td>
<td>1</td>
<td>0.5420</td>
<td></td>
<td>closest to threads</td>
</tr>
<tr>
<td></td>
<td>2</td>
<td>0.5425</td>
<td></td>
<td>no significant difference Dia. 1 vs Dia. 2</td>
</tr>
<tr>
<td></td>
<td>3</td>
<td>0.5440</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>4</td>
<td>0.5440</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>5</td>
<td>0.5450</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>6</td>
<td>0.5460</td>
<td></td>
<td></td>
</tr>
<tr>
<td></td>
<td>7</td>
<td>0.5465</td>
<td></td>
<td>closest to head</td>
</tr>
</tbody>
</table>

Whoa!

 

[Glen]

@Tazzieman - Sorry about that - this bulletin board totally screws up the TABLE tag and turns it into garbage. After three attempts I finally just posted plain text in a CODE block. See above for a more readable presentation.

@Stu_Barnes - can someone fix how TABLE code renders? I'm happy to provide examples offline if it'll help.